CCNP Routing 642-902

Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing table. You are also not able to see the R4 Ethernet subnet on the R1 routing table. Which configuration change should be made to resolve this issue? Select the routers where the configuration change will be required, and select the required EIGRP configuration command(s). (Choose two.)

A. R1 and R4
B. R2 and R3
C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary-address eigrp 1
D. variance 2
E. eigrp stub connected
F. no auto-summary
Answer: BF
For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Routing 642-902

Refer to the exhibit. You are the network administrator responsible for the NProuter, the 10.1.1.1 router, and the 10.1.1.2 router. What can you determine about the OSPF operations from the debug output? Select the best response.


A.The NProuter has two OSPF neighbors in the “Full” adjacency state.
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds.
C.The NProuter serial0/0 interface has been configured with an OSPF network type of “point- to-point”.
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting.
E.The “Mismatched” error is caused by the expiration of the OSPF timers.
Answer: B
For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Routing – 642-902

Which two routing protocols require a metric to be configured when redistributing routes from other protocols? (Choose two.)
A.RIP
B.OSPF
C.EIGRP
D.IS-IS
E.BGP
Answer: AC
For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Routing – 642-902

A company has a BGP network and a BGP route of 196.27.125.0/24 that should be propagated to all of the devices. The route is not now in any of the routing tables. The administrator determines that an access list is the cause of the problem. The administrator changes the access list to allow this route, but the route still does not appear in any of the routing tables. What should be done to propagate this route?
A.Clear the BGP session.
B.Use the release BGP routing command.
C.Use the service-policy command to adjust the QOS policy to allow the route to propagate.
D.Change both the inbound and outbound policy related to this route.
Answer: A

For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Routing – 642-902

Which command displays statistics on EIGRP hello, updates, queries, replies, and acknowledgments?
A.    debug eigrp packets
B.     show ip eigrp traffic
C.     show ip eigrp topology
D.    show ip eigrp neighbors
Answer: B

For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Route - 642-902

Which two statements about 6to4 tunneling are accurate? (choose two)
Select the 2 best responses.
A. Prepending a reserved IPv6 code to the hexadecimal representation of 192.168.0.1 facilitates 6to4 tunneling
B. 2002::/48 is the address range specifically assigned to 6to4
C. Each 6to4 site receives a /48 prefix in a 6to4 tunnel
D. Prepending 0x2002 with the IPv4 address creates an IPv6 address that is used in 6to4 tunning
E. 6to4 is a manual tunnel method
Answer: CD

For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Route - 642-902

When learning a new route, if a LSA received is not found in the topological database, what will an internal OSPF router do?
Select the best response.
A. The sequence numbers are checked, and if the LSA is valid it is entered into the topology database.
B. The LSA is placed in the topological database and an acknowledgement is sent to the transmitting router.
 C. The LSA is dropped and a message is sent to the transmitting router.
D. The LSA is flooded immediately out of all the OSPF interfaces, except the interface from which the LSA was received.
Answer: D

For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP Route - 642-902

What are two Cisco IOS commands that can be used to view neighbor adjacencies? (Choose two.)
Select 2 response(s).
A. show ip ospf database
B. show ip ospf neighbors
C. show ip ospf protocols
D. show ip ospf interfaces
Answer: BD

For Best CISCO/MCITP/LINUX/EXCHANGE SERVER/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP 642-902

You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configurations are correct for generating type 3 LSAs?
Select the best response.
A. Internal routers within the backbone area (area 0)
B. Internal routers within the NSSAs
C. Internal routers within the stubby areas
D. ASBRs
E. ABRs
F. DRs and BDRs
Answer: E
For Best CISCO/MCITP/LINUX/EXCHANGE SERVR/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook

CCNP 642-902

The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?
Select the best response.
A. show ip ospf [process-id] interface
B. show ip ospf neighbor
C. show ip ospf [process-id]
D. show ip ospf [process-id area-id] database
Answer: B
For Best CISCO/MCITP/LINUX/EXCHANGE SERVR/PC HARDWARE AND  NETWORKING Training visit www.zoomgroup.com
Join us on facebook